17-1/2x27x5 (17.5 x 26.2 x 5) MERV 13 American Standard Aftermarket Replacement Filter (2 Pack)


American Standard

Price: $79.98

Product Details

  • It is up to twenty times more impressive than ordinary fiberglass filters.
  • No set-up required...no combs needed...filter just slides right in!
  • The in name only size is 17 1/2 x 27 x 5. The actual size is 17.2 x 26.2 x 5.

American Standard Freedom 80 Furnace Problem

Furnace starts normally, but flames out after 3 to 10 minutes.


Where is the location of the Hi Limit Switch on an American Standard Furnace?

Jan 16, 2009 by yea, sure. | Posted in Maintenance & Repairs

serial tot up:
TXC037C4HPB1
where is the thermostat on it?

if you that the higher panel off the furnaceyou will see the hi limit switch it as about 6 wire to it.

DICK R | Jan 16, 2009

should be on thermostat
the lock man | Jan 16, 2009

The limit thrash will be inside the panel and behind the burners. Again, unless you have some heating/cooling experience, I would not suggest messing around with the limit twitch.
Dolphin Dawn | Jan 16, 2009

if you that the upland panel off the furnaceyou will see the hi limit switch it as about 6 wire to it.
DICK R | Jan 16, 2009

that ideal # looks like a heat pump "air handler",any "high limits" that breathe in it are located in the top compartment called the auxillary heat package,,best to have an hvac tech certificate/replace those......if its a relatively new GAS furnace [15 years old or less] then the high limit switch will have 2 wires connected to it and will be located honourable above the burners in an 80% eff furnace [metal vent pipe],,or just below the burners in a 90%+ eff [pvc bogus vent pipe] furnace...the wires are usually yellow..the limit is held in place by 2 screws on the sides of the limit......as far as the "thermostat",,do you ungenerous the actual "klixon" switch part of the limit that inserts into the furnace when its mounted?,,its all the same part.....the "face ruin thermostat" is obviously in the home on a wall,dont quite understand what your asking on that part of proposition beyond the shadow of a doubt......dan
DAN THE AC MAN | Jan 16, 2009

there are other switches that might requisite to be reset too. Check every little component inside and out on your furnace. If a component has a little button then strike dismissal it because it might be a reset.
Chris | Jan 16, 2009

Where is the thermostat on the American Standard Furnace?

Jan 16, 2009 by yea, sure. | Posted in Maintenance & Repairs

is there a seperate thermostat on the furnace itself?

Can I adjust the variable speed fan on my American Standard furnace for heat pump usage? Only runs slow now.?

Feb 04, 2009 by Zach | Posted in Maintenance & Repairs

The two gas rouse stages run variable, but the heat pump only blows air at the lowest possible setting. This does not consider the heat pump to meet t-stat demands. I need a little more speed, maybe 5 or 10% more. 20% or more may be too much.

yes , there is a cfm locale on the back of blower door . need to set dip switches.

gratedeaddog | Feb 04, 2009

American Standard Furnaces - News


Water-saving toilets reduce wastefulness in homes Casa Grande Valley Newspapers
- Mar 25, 2009
Weaken-saving toilets reduce wastefulness in homesCasa Grande Valley Newspapers, AZThe following companies put up for sale water-saving toilets: American Standard, (800) 442-1902, www.americanstandard-us.com; Briggs Plumbing, (800) 627-4443, www.briggsplumbing.com; Kohler, (800) 456-4537, www.us.kohler.com; and Saniflo, (800) 363-5874,

FACTBOX-Mines and plants hit by low prices, high costs Forbes
- Mar 25, 2009
FACTBOX-Mines and plants hit by low prices, excessive costsForbes, NYMarch 20 - South African ferrochrome producer Hernic said it close all its four furnaces at the start of this year. March 20 - Geovic Mining Corp. said it will slash costs, modify in scale and delay by at least a year its Nkamouna